Welcome to our delightful plushy crafting adventure, where we’ll show you how to create a charming heart plushy perfect for Valentine’s Day and beyond. What makes this heart plushy extra special is its connection with our Valentine’s Day Teddy Bear tutorial.
This versatile pattern can be used to make not only plushies, but also bag charms, coin purses, and more, making it a must-have addition to your crafting repertoire.
Whether you’re gifting it to a loved one or adding a touch of whimsy to your own accessories, this heart plushy is sure to bring joy and warmth wherever it goes. Join us as we bring this adorable heart plushy to life, one stitch at a time!
인쇄 설정을 확인하여 패턴 크기가 조정되지 않았는지 확인하세요. 각 페이지 하단에 있는 참고 자료를 측정하여 제대로 인쇄되었는지 확인할 수 있습니다.
가죽에 패턴 조각을 고정하기
Roughly cut around the different pieces of the heart with an X-acto knife or a pair of scissors.
마스킹 테이프를 사용하여 패턴의 모든 부분을 가죽에 고정하세요.
바느질 구멍 펀칭
스티칭 프롱이나 홀 펀치를 사용하여 종이와 가죽에 직접 스티칭 구멍을 뚫습니다.
Use you 7.5mm hole punch to punch-out the extremities of the zipper’s slot.
Cutting-out all the pieces of the plushy
Follow along the edges of printed pattern elements with your pair of scisors or X-acto knife to cut-out all the pieces of the heart.
Painting the heart (optional)
I didn’t have any red leather so I chose to paint some parts of the plushy to obtain the result that I had in mind.
Feel free to express your creativity here! Or shall I say…follow your heart?!
Stitching the zipper
To setup the zipper to the back, apply some contact cement on the flesh side around the edges of the slot.
Apply contact cement to the zipper as well and glue it in place on the back piece. Gently hammer around the perimeter of the slot in order to insure a good bond between the leather and the zipper.
Stitch the zipper in place using a saddle stitch.
Embroidering the heart and stitching it to the front
Embroider the inscription on the heart either using a saddle stitch or a back stitch.
For purely decorative stitches like this I favor the back stitch as it gives a very consistent stitching lines whereas saddle stitching creates slightly slanted thread segments between the holes.
You can then stitch the heart to the front piece.
Stitching the 3 layers of the plushy together
The plushy is stitched with the inside facing out. You will need to stitch 3/4 of the perimeter while leaving an opening in order to turn the heart inside out.
We need to create two compartments, one for the secret pocket at the back and the other to hold the stuffing at the front. This is achieved by treating the partition and the back as a single layer when they are being stitched to the front.
Once you have stitched around 3/4 of the perimeter, turn the heart inside out.
The most difficult part in turning leather pieces like this inside out is to get an initial pinch between your fingers (with your fingers going through the opening, trying to grab the opposite edges from the inside). Once you’ve pinched the edges you can pull them inward, stick a blunt object in the depression created on the flesh side and start gently pushing towards the opening. From then on the hardest part is done. The rest is just a patient game of pushing and pulling but really that first pinch is the crux of it all.
If you intend to use the plushy with the teddy bear, insert two magnets and position them at the top right and left corners.
Add the stuffing to the heart.
The magnets are simply held in place thanks to the pressure of the stuffing around.
Pay attention to the polarity of the magnets, especially in relation to the magnets that you set-up in the teddy bear’s arms. Otherwise your poor teddy will forever be unable to hold on to its heart…
Once the magnets are in place and the stuffing added, finish stitching along the perimeter of the heart.
When I get to that point I switch my default stitching position to having both threads coming out from the top grain side through opposite holes. This way it becomes easy to tension the thread after each stitch and to progressively close the gap between the two edges being stitched together.
최종 결과
이 튜토리얼을 따라가면서 즐거운 시간을 보내셨기를 바랍니다. 아래 댓글에 창작 사진을 게시해 보세요. 나의 작은 프로젝트를 당신의 것으로 만들어 세상에 내놓는 것을 보는 것은 나에게 큰 의미가 있을 것입니다.
여기에 게시되기를 원하는 이 튜토리얼이나 프로젝트 아이디어에 대한 피드백/질문은 언제든지 환영할 것입니다.
즐거운 만들기!
각주
다음 온라인 콘텐츠는 이 프로젝트를 만드는 동안 약간의 도움 및/또는 영감을 제공했습니다.
귀하가 소셜 로그인 버튼을 사용하여 처음 로그인하는 경우 당사는 귀하의 개인 정보 보호 설정에 따라 소셜 로그인 제공업체가 공유한 귀하의 계정 공개 프로필 정보를 수집합니다. 또한 당사 웹사이트에서 귀하를 위한 계정을 자동으로 생성하기 위해 귀하의 이메일 주소를 얻습니다. 계정이 생성되면 이 계정에 로그인됩니다.
동의하지 않는다동의하다
계정 생성을 허용합니다
귀하가 소셜 로그인 버튼을 사용하여 처음 로그인하는 경우 당사는 귀하의 개인 정보 보호 설정에 따라 소셜 로그인 제공업체가 공유한 귀하의 계정 공개 프로필 정보를 수집합니다. 또한 당사 웹사이트에서 귀하를 위한 계정을 자동으로 생성하기 위해 귀하의 이메일 주소를 얻습니다. 계정이 생성되면 이 계정에 로그인됩니다.
지도 시간
하트 플러시
2시간
쉬운
가죽공예의 공통점
Welcome to our delightful plushy crafting adventure, where we’ll show you how to create a charming heart plushy perfect for Valentine’s Day and beyond. What makes this heart plushy extra special is its connection with our Valentine’s Day Teddy Bear tutorial.
This versatile pattern can be used to make not only plushies, but also bag charms, coin purses, and more, making it a must-have addition to your crafting repertoire.
Whether you’re gifting it to a loved one or adding a touch of whimsy to your own accessories, this heart plushy is sure to bring joy and warmth wherever it goes. Join us as we bring this adorable heart plushy to life, one stitch at a time!
요구사항
기술
도구
BOM
무늬
하트 플러시 패턴
무료!연습
패턴 인쇄
당신은 할 수 있습니다 여기서 패턴을 얻으세요 아직 하지 않았다면.
다운로드한 버전에 따라 US Letter 또는 A4 용지에 인쇄하세요.
인쇄 설정을 확인하여 패턴 크기가 조정되지 않았는지 확인하세요. 각 페이지 하단에 있는 참고 자료를 측정하여 제대로 인쇄되었는지 확인할 수 있습니다.
가죽에 패턴 조각을 고정하기
Roughly cut around the different pieces of the heart with an X-acto knife or a pair of scissors.
마스킹 테이프를 사용하여 패턴의 모든 부분을 가죽에 고정하세요.
바느질 구멍 펀칭
스티칭 프롱이나 홀 펀치를 사용하여 종이와 가죽에 직접 스티칭 구멍을 뚫습니다.
Use you 7.5mm hole punch to punch-out the extremities of the zipper’s slot.
Cutting-out all the pieces of the plushy
Follow along the edges of printed pattern elements with your pair of scisors or X-acto knife to cut-out all the pieces of the heart.
Painting the heart (optional)
I didn’t have any red leather so I chose to paint some parts of the plushy to obtain the result that I had in mind.
Feel free to express your creativity here! Or shall I say…follow your heart?!
Stitching the zipper
To setup the zipper to the back, apply some contact cement on the flesh side around the edges of the slot.
Apply contact cement to the zipper as well and glue it in place on the back piece. Gently hammer around the perimeter of the slot in order to insure a good bond between the leather and the zipper.
Stitch the zipper in place using a saddle stitch.
Embroidering the heart and stitching it to the front
Embroider the inscription on the heart either using a saddle stitch or a back stitch.
For purely decorative stitches like this I favor the back stitch as it gives a very consistent stitching lines whereas saddle stitching creates slightly slanted thread segments between the holes.
You can then stitch the heart to the front piece.
Stitching the 3 layers of the plushy together
The plushy is stitched with the inside facing out. You will need to stitch 3/4 of the perimeter while leaving an opening in order to turn the heart inside out.
We need to create two compartments, one for the secret pocket at the back and the other to hold the stuffing at the front. This is achieved by treating the partition and the back as a single layer when they are being stitched to the front.
Once you have stitched around 3/4 of the perimeter, turn the heart inside out.
The most difficult part in turning leather pieces like this inside out is to get an initial pinch between your fingers (with your fingers going through the opening, trying to grab the opposite edges from the inside). Once you’ve pinched the edges you can pull them inward, stick a blunt object in the depression created on the flesh side and start gently pushing towards the opening. From then on the hardest part is done. The rest is just a patient game of pushing and pulling but really that first pinch is the crux of it all.
If you intend to use the plushy with the teddy bear, insert two magnets and position them at the top right and left corners.
Add the stuffing to the heart.
The magnets are simply held in place thanks to the pressure of the stuffing around.
Pay attention to the polarity of the magnets, especially in relation to the magnets that you set-up in the teddy bear’s arms. Otherwise your poor teddy will forever be unable to hold on to its heart…
Once the magnets are in place and the stuffing added, finish stitching along the perimeter of the heart.
When I get to that point I switch my default stitching position to having both threads coming out from the top grain side through opposite holes. This way it becomes easy to tension the thread after each stitch and to progressively close the gap between the two edges being stitched together.
최종 결과
이 튜토리얼을 따라가면서 즐거운 시간을 보내셨기를 바랍니다. 아래 댓글에 창작 사진을 게시해 보세요. 나의 작은 프로젝트를 당신의 것으로 만들어 세상에 내놓는 것을 보는 것은 나에게 큰 의미가 있을 것입니다.
여기에 게시되기를 원하는 이 튜토리얼이나 프로젝트 아이디어에 대한 피드백/질문은 언제든지 환영할 것입니다.
즐거운 만들기!
각주
다음 온라인 콘텐츠는 이 프로젝트를 만드는 동안 약간의 도움 및/또는 영감을 제공했습니다.